Create 3D Model for printing from PSD logo

Estado: Closed
Premio: $240
Propuestas recibidas: 35
Ganador: yop1172

Winner

Resumen del concurso

Design a 3D model based on the logo PSD provided that can be easily 3D printed from STL format.

The model is going to be 3D printed quite large and used in our office. We can paint and texture the model once printed, so we're open to any colors or other ideas for the model as well.

The more detailed, creative or just damn cool the model created is the better.

Thanks for the early submissions folks.

The intent is for the 2D logo to be recreated in 3D with the ability to be 3D printed from an STL format.
3D Render and object can be in any program as long as an STL output can be provided.

It will be 3D Printed as a free standing object, like a trophy.

For more detail, the spray paint can should be rendered as a cylinder, the "D" logo can be dealt with in a creative manner of the designers choice. Either rendered as a label on the can that stands out, or carved into a hollow section of the spay can.

The paint dripping from the side of the can should be used as a stand for the model and a base plate for the model to stand upright should be added to the bottom of it. Perhaps the 3D paint dripping off the can is made to look like it is pooling on the ground as the base plate. The can itself should be rendered on an angle from horizon as it is in the PSD.

Thanks!

Habilidades recomendadas

Winner

Publica un concurso similar

Comentarios del empleador

“Excellent designer, very responsive. Will absolutely work with again in the future.”

mlegary, Canada.

Principales propuestas de este concurso

yop1172 Mexico

0
deep075 United Arab Emirates

0
VolcanoTeam Turkey

0
artseba185 Argentina

0
peabodybrando India

0
februaryproj Thailand

0
chonoman64 Dominican Republic

0
keerthirajan25 India

1
Stebas89 Australia

0
bdas3d India

0
bdas3d India

0
bdas3d India

0
unreal0044 Sri Lanka

0
keerthirajan25 India

0
Cobot Estonia

0
constantino1983 Philippines

0

Ver más participaciones

Tablero de aclaración pública

govind14598
- 3 años atrás
please chek out entry no #55
- 3 años atrás
bdas3d
- 3 años atrás
Dear contest holder- Please consider the stability and weight of the model also ( center of gravity point should be inside the model), beside the aesthetic design .
- 3 años atrás
Kindland
- 3 años atrás
Good luck printing that...
- 3 años atrás
1. keerthirajan25
  - 3 años atrás
  Exactly... Countless support structure would ruin the surfaces while removing
  - 3 años atrás
MosTafa1Ramadan
- 3 años atrás
Working will make better result
- 3 años atrás
Devpro11
- 3 años atrás
Since you want to model for 3d printing, I have prepared a realistic 3d printing file(stl).
- 3 años atrás
Devpro11
- 3 años atrás
How are you?
- 3 años atrás
nanangkh
- 3 años atrás
Please review #40
- 3 años atrás
facefromdream
- 3 años atrás
Maximum height with stand?
- 3 años atrás
Kindland
- 3 años atrás
Hello @Contest Holder, do you want the Trophy to be made out of multiple pieces connected with keyholes, or one full watertight piece?
- 3 años atrás
coc3dart
- 3 años atrás
working
- 3 años atrás
sharkfreelancer
- 3 años atrás
first, where will you use it.. on the wall or on the office as a decoration it's important to know
- 3 años atrás
1. Organizador del concurso
  - 3 años atrás
  It will be 3D Printed as a free standing object, like a trophy
  - 3 años atrás
banigandlapati
- 3 años atrás
I don't think you just need a extruded version of you logo. Please elaborate your requirement.
- 3 años atrás
1. Organizador del concurso
  - 3 años atrás
  I've added to the original description and above
  - 3 años atrás
Karimaziz1
- 3 años atrás
what is size of the model you want?
- 3 años atrás
1. Organizador del concurso
  - 3 años atrás
  The model should be no less than 420mm in total height.
  - 3 años atrás
Organizador del concurso
- 3 años atrás
Thanks for the early submissions folks. The intent is for the 2D logo to be recreated in 3D with the ability to be 3D printed. For more detail, the spray paint can should be rendered as a cylinder, the "D" logo can be dealt with in a creative manner of the designers choice. Either rendered as a label on the can that stands out, or carved into a hollow section of the spay can. The paint dripping from the side of the can should be used as a stand for the model and a base plate for the model to stand upright should be added to the bottom of it. Perhaps the 3D paint dripping off the can is made to look like it is pooling on the ground as the base plate. The can itself should be rendered on an angle from horizon as it is in the PSD. Thanks!
- 3 años atrás
kartikv1
- 3 años atrás
Please check entry#6
- 3 años atrás
fahryalw
- 3 años atrás
do you have any design
- 3 años atrás
1. Organizador del concurso
  - 3 años atrás
  It is attached to the description
  - 3 años atrás
omar019373
- 3 años atrás
Please provide with me more details.
- 3 años atrás