Arduino Jobs

integrar whatsapp-twilio-webservice, para gestionar una URL que pueda activar la salida logica de un ESP8266

El proyecto consiste en realizar un hadware para una pantalla donde conectada al teléfono puedes modificarla conectada a una aplicación al teléfono

An instrumented electrically maintained mechanical oscillator is to be monitored to detect and measure very small changes in period over the long term. Details in confidence if interested.

Write 4 wheel differential drive control code for a robot having 4 motors using BTS9760 motor drivers and My1016z3 motors. The robot will be controlled using flysky remote transmitter and arduino will have its reciver. The code should be based on kinematics and equation of motion. The required maximum speed is 70rpm and motors have a rated speed of 300 rpm.

Simple app, that it will be active when my external HW is connected via Bluetooth. When it is active microfon must be muted. When I press button on my BT device phone mic must be enabled, when I release button mic will be muted again. (PTT Press To Talk)

During knee surgery recovery, when specified by your doctor, you are allowed to put a certain amount of body weight on the affected knee. This app would link with sock/shoe mounted pressure sensors and processor to alert you when you have reached the weight threshold, and provide alerts when that threshold is exceeded.

ESP32 high rate parallel data out/input Proof of ability to connect fast BUS to ESP32. The goal right now is a 4-bit connection at a rate of 16.368 MS/sec, but the test is generic. In the test we will connect a BUS between two ESP32's with a clock where one will be used as a transmitter and the other as a receiver .The data can be entered into the transmitter in any form (.WIFI, Ethernet, USB etc. ) and prove their correctness in the receiver by comparison, or CRC or another idea

A scale using esp32 and Hx711 that displays the current output on an i2c 7 segment 4 digit display. Also when an nfc tag is detected it associates said entity with weight and publishes the two to a Google sheet.

We have recently had a PCB designed to operate with BQ34Z100PW-G1 for gauge and BQ24170RGYR as our battery charging circuit controller. The circuit does not seem to be functioning with the code we currently have. We have tried a couple different solutions but realize we are in need of someone who is familiar with both parts, hardware and software designs. We can provide the circuit and all of the specific information needed to view where we are with the design. We would be able to share the current code we have for the devices, as well as we have the ability to help with debugging and trouble-shooting the physical circuit if needed. Custom PCB Python BQ34Z100PW-G1 BQ24170RGYR

I need to write a python code to scan QR from camera module of Pi. There can One QR over the package or two QR over the package or No QR over the package. on the basis of above condition activate GPIO

• I need to monitor 5 outlets of 110VAC each and the temperature of an environment. • I need to know exactly when the energy drops and returns at each of the 5 points. • All energy and temperature points are in the same room. • There is a WIFI connected to the UPS and with a 4G chip. • The internet does not fail even in case of power failure. • Locally, there is a small server also connected to the wifi and the UPS that sends SNMP events to two external servers, ZABBIX and PRTG. • I need to monitor the drop and return of energy in these 5 energy points and know the ambient temperature. In short, on ESP32 or ARDUINO: 1) Make the list of material to be purchased; 2) Make a program that generates events via SNMP to a local server (cable or wifi) with a spec...

Funkce kódu by měla být Na displeji arduina budu mít osm řádků očíslováním 1 až 8. Vždy jeden řádek bude obsahovat polohu krokového motoru a natočení servomotorku Arduino. Pomocí klávesnice v řádku vepíši vzdálenost v milimetrech a úhel natočení servo motorku Po stisknutí koncového spínače dojede k najetí polohy Po opakovaném stisknutí koncového spínače dojde k načtení 2 řádku 3..... 8 a tak stále dokola.

We are looking to do troubleshoot our existing program and do some modifications so we need 4 to 5 days of PLC programming in Siemens S7 200(Microwin) and Exor HMI (J mobile).

I have pt100 temperature sensor signal connected to plc put the signal is not stable as there is many noise come from vfd so I need low pass filter circuit to enter the pt100 signal on it to make filter of any other noise

in 10 steps, 5 seconds each Electronics knowledge required

I created a Code for a Wallbox, so that Hotel Guests are able to use their Hotel Room Cards to start a charging process. The Code basically checks the validation of the Room Card, reads the Room Number of the Card, and transmits Room Number and the authorization to the MQTT Server. The Charging Station does the rest and sends an Email at the End. The Code works, but I have some hickups with collecting the mqtt Data of the current charging Rate and total Amount. Now I thought if it would be possible to use it with Tasmota, so I would be able to edit the Script from Remote, and don't have to flash the pcb onsite if changes are needed.

Hello, I have a arduino mega project with LCD, initially which was started with arduino uno and rotary encoder to feed commands. But now we want to upgrade it to arduino mega and LCD. We already have a code for the same and want to debug and add all the required codes and make a perfectly working model as per our needs. One should be very thorough with arduino mega and GUI design on LCD for the project.

I have a 1970s Pioneer SX-626 stereo receiver that has some static in the left channel. I'm guessing some transistors need replacement.

We are developing second release of EntiaLiving Smart Home Sustem

This is re-posting of an earlier project with refined requirements and specifications. The project is a c++ XIAO embedded system which reads the IMU, PDM microphone and a future MS58 pressure sensor. The project connects to a iPhone using five BLE characteristic for data and control. The code will use public Arduino and nRF52 libraries. The client will add the MS pressure sensor the to project after acceptance. The client is a developer and will be able to assist and help debug. It is preferred the selected developer also code the matching iOS app using Xcode and SwiftUI. The iOS app connects to the XIAO as the central and is the display device for the data collected from the XIAO. If you are available to immediately start this project please request the SOW.

- I need someone to send data to an LED panel. - The driver being used in the hardware is mbi5124gp.

I need to develop pressure sensor based coding for ESP32 mcu. Here, I am planning to use US9111 pressure sensor with mcp3421 ADC converter. I want to measure +5PSI to -5PSI pressure value, with auto zero calibration. When there will no pressure on the pressure sensor that must be zero value at the initial condition. It should be strictly maintain. It can be set by auto zero calibration. I want to measure pressure precisely, so you need to do the coding with exact calculation.

Por favor, regístrate o inicia sesión para ver los detalles.

I need to make mini geared stepper motor do one 360° turn Need to have screen showing timer and be able to adjust time in minutes example : Do one turn every 5 minutes

I need someone that has knowledge of this, to draw a graph from serial input which will be from an ADC on the MCU and given to the communication port via RS232. I should be able to save this as a CSV file and open it later in excel and the software itself. Software must be able to give me pane view and compress view. Deliverable is source code project file.