Ingeniería estructural Jobs

Necesito desarrollar en AutoCAD los planos completos para un pequeño complejo de servicio interno que incluya: • Una estación de resguardo de combustible de 8 × 8 m donde irán instalados un tanque de gasoil de 15 000 L y otro de gasolina de 5 000 L. • Un almacén auxiliar (aún sin medidas definidas; acepto tu propuesta optimizada). • Una cocina de tamaño reducido ‑similar o menor a la de una ducha-, con un área de preparación y un espacio anexo para almacenar alimentos. • Un salón pequeño contiguo a la cocina (dimensiones por definir juntos). Requiero que los planos entreguen, como mínimo: - Arquitectónico de ubicación y distribución general. - Detalles estru...

Busco un profesional que suministre y coloque “La rejilla caja en centro” a lo largo de un área de Entre 10 y 30 m² dentro de un lavadero de coches situado en San Fernando de Henares. Necesito rejillas metálicas que sean Resistente a productos químicos para soportar detergentes, desengrasantes y otros líquidos habituales en el lavado de vehículos. La instalación debe quedar nivelada, con la pendiente adecuada hacia la caja central, sin levantamientos ni fisuras en el suelo existente. Entrego el local vacío y con acceso para descarga de material; el instalador debe traer todas las herramientas, fijaciones y elementos de sellado necesarios. Entiendo que cada proyecto tiene sus particularidades, por eso agradeceré...

I am looking for a structural engineer to design the structural elements for a residential rear and side extension in London and provide the required calculations and drawings for Building Control approval. The engineer must have experience with UK residential buildings and be familiar with UK Building Regulations. You should also understand how to prepare documents suitable for Building Control submission. Scope of work includes: Structural design for the rear and side extension Structural calculations Structural drawings if required Documents suitable for Building Control approval Please apply only if you have relevant UK experience.

I need a qualified structural engineer to assess diagonal cracks on the walls of two properties we are detailing with following RICS level 2 surveys The survey should include: - Detailed inspection of all affected areas. - Identification of potential causes. - Recommendations for repair or mitigation. - A comprehensive report documenting findings. Ideal skills and experience: - Licensed structural engineer. - Experience with residential properties. - Strong analytical and report-writing skills.

I need a qualified structural engineer to assess diagonal cracks on the walls of two properties we are detailing with following RICS level 2 surveys The survey should include: - Detailed inspection of all affected areas. - Identification of potential causes. - Recommendations for repair or mitigation. - A comprehensive report documenting findings. Ideal skills and experience: - Licensed structural engineer. - Experience with residential properties. - Strong analytical and report-writing skills.

I'm looking for a skilled professional to do a calculation on the drawings (attached) of a concrete foundation for a large public sculpture. Requirements: - The sculpture is over 4.5m high and weighs 3 tonnes. - Hi I am a sculptor and industrial designer. I wish to get a brief overview on my foundation design. I can only go .5 m into ground due to services running closeby I wish to site the base down .5m and with ,25m over the ground with 1.4mcu of concrete the steel and stone arc just 100 degrees of a circle 1.2 wide x 4.3m radius will have I beam type steepl with stone infills approx 3 tonnes. The foundation must be sturdy and durable to support the weight and height of the sculpture. Sculpture must survive a wind loading of minimum 120km/hr winds Ideal Skills: - Experience wit...

I'm looking for a structural engineer to sign/prepare plan for submission to construct a 20x20 open/detached carport. The carport will primarily serve as vehicle parking. Key requirements include: - Use of 8x8 pressure-treated posts - Metal roof - No additional storage areas, just the carport Ideal skills and experience: - Experience with wood and metal construction - Knowledge of building codes and regulations - Ability to ensure structural integrity and durability Please provide examples of similar work and a detailed estimate.

Job Description: Create accurate 3D CAD models of iron/steel cab structures using Rhino Produce manufacturing-ready drawings Apply proper tolerances, material specs, and fabrication methods Collaborate with engineering/fabrication teams to refine designs Requirements: Proven experience with Rhino or SolidWorks (or equivalent CAD tools) Strong background in metal/iron fabrication and structural design Ability to work from sketches, 2D drawings, or concept designs Attention to detail and adherence to manufacturing standards

I need a consultation to determine if iron L brackets can replace old timber knee supports in my dairy barn. The goal is to remove a tripping hazard caused by obstructions on a wooden barn floor. Ideal Skills and Experience: - Structural engineering knowledge - Experience with agricultural buildings - Familiarity with safety standards in barn environments - Practical experience in using and installing iron L brackets

I already have a complete set of plans and calculations for a single-family prefabricated ADU. All that’s missing is a California-licensed civil engineer’s review and professional stamp so I can submit the package to the local building department. Here’s what I need from you: • Perform a quick yet thorough civil review of the existing drawings and calcs to confirm compliance with California Building Code and any typical municipal requirements. • Identify any minor adjustments required for approval (if any) and note them clearly so my drafter can revise. • Provide a signed and sealed PDF set (and, if necessary, a wet-signed hard copy) that I can upload or hand-deliver to the city. • Issue any accompanying certification letter the jurisdiction ma...

All of the drawings, details, and structural calculations for my prefab accessory dwelling unit are ready to go—I simply need a California-licensed civil engineer to review them and add a professional stamp and signature. The project is a residential ADU that will be rented out, so the city’s submittal package must be airtight. Scope I will email you the full PDF set (plans, calcs, and any supporting documents). After your review, I’m looking for your digital stamp and signature on the sheets that require it, along with a short review letter confirming code compliance. Deliverables • Digitally stamped and signed plan set in PDF • One-page review/approval letter (PDF) • Any minor redline comments, if needed, returned in the same file Acceptance Cr...

I'm looking for a structural expert to provide the necessary I-beam sizes and C-purlins (30 x 50 x 14) for a residential building with a 4:12 pitch open span. Requirements: - Steel I-beams and C-purlins - Open span with a 4:12 pitch - Must include sizes for I-beams and necessary C-purlins - Steel needs painting for corrosion resistance Ideal Skills and Experience: - Structural engineering background - Experience with residential building projects - Proficiency in steel structural design - Knowledge of structural integrity and load-bearing requirements Please provide detailed specifications and ensure accuracy in measurements.

I need a full set of permit-ready drawings for a compact modern home between 600 – 800 sq ft here in California. The layout is simple: one bedroom, open living-kitchen area, and a bathroom, all designed with clean, contemporary lines. A stamped structural foundation plan is essential. I’m looking for a pier-and-beam solution (sometimes called pier and post), detailed to meet current California Building Code requirements and local seismic and energy (Title 24) standards. Please include: • Architectural floor, roof, and elevation sheets • Structural calculations and details for the pier-and-beam foundation • Title 24 energy documents • PDF set ready for the city plus the original CAD files for future tweaks If you’re licensed to stamp in ...

I’m ready to move forward with a two-container residence—two 40 ft shipping containers joined into a single-story, 6 feet between container, 2 feet above the ground, open-floor-plan home with 2 bedrooms —on my 2.5-acre parcel in Paulden, AZ. Because the lot sits in a mapped flood zone, I need a permit package that satisfies Yavapai County building and flood-plain regulations. Here’s what I need from you: • Site plan and layout that clearly positions the containers, parking, setbacks, and required drainage features on the property. • Detailed architectural drawings suitable for county submittal, showing foundation, structural tie-ins between the containers, roof framing, elevations, and any flood-proofing details. • Structural engineering c...

I need a complete structural evaluation carried out in ANSYS Workbench for a mechanical component that is already modeled. The task is strictly structural—no thermal or fluid-flow coupling—so please focus on static strength, deformation, and, if you judge it helpful, a brief modal check for natural frequencies. This is a single part, not a building, bridge, or aerospace assembly. You will receive: • the clean STEP file of the component • loading diagrams with magnitudes, directions, and boundary conditions Your job: • import and clean the geometry, create a high-quality mesh, and document your mesh-independence check • apply the supplied loads and constraints, then solve for von Mises stress, principal stresses, displacements, and safety factor ...

Preciso que um edifício metálico industrial seja totalmente modelado no Tekla Structures. Fornecerei especificações detalhadas e fotos do local para servir de referência; não há desenhos técnicos disponíveis, portanto será importante interpretar corretamente cada detalhe das especificações. Desejado: • Criar o modelo 3D completo do edifício no Tekla, incluindo perfis, ligações, parafusos e chapas de acordo com a norma EN 1090-2 | EXC2 • Geração de listas de aprovisionamento, peças, conjuntos, parafusaria e expedição. • Produzir conjunto de desenhos de fabricação e montagem diretamente a partir do modelo. A legenda do des...

I have a full set of structural drawings in PDF and need an experienced civil engineer or quantity surveyor to convert them into a precise Bill of Quantities. The focus is on reinforced concrete works (RCC), plain cement concrete (PCC), isolated footings, ground beams/columns and all associated earthwork. Accuracy is critical; the figures you provide will feed directly into cost planning and procurement, so every dimension has to align with the drawings. I will share the PDF immediately after we agree to work together. Deliverables • An itemised BOQ covering RCC, PCC, footing, column and earthwork quantities • Clear measurement notes or assumptions for any ambiguous details • Editable file (Excel preferred, but I’m open to your usual format) Acceptance cri...

I need an experienced solar PV design engineer who can jump straight into a small-scale residential project and turn around professional drawings and calculations without delay. The site offers less than 1,000 sq. ft. of usable roof space, and the homeowner’s primary objective is to cut monthly electricity bills, so every watt and panel placement must be optimised for cost-to-benefit. You’ll receive roof photographs, basic structural information, and recent utility bills as soon as we start. From there I expect a full design package that can be handed to the local installer and utility for approval. Please rely on industry-standard tools you’re comfortable with—PVsyst, HelioScope, AutoCAD, SketchUp, or similar—to validate shading, estimate annual energy yield...

Remote Works Design Engineer Work Type Remote (Part-time or Full-time Contract) Project Locations Jordan & Iraq (remote design support) Role Summary We are looking for a Temporary Works Design Engineer who can work remotely and support engineering design for projects in Jordan and Iraq. The engineer will provide design calculations, drawings, and technical support for construction temporary works. Required Design Experience The engineer must have proven experience designing: Pile working platforms for piling rigs and heavy equipment Cofferdam systems (sheet piles, bracing, excavation support) Concrete formwork systems Thrust blocks for pipelines Responsibilities Prepare engineering calculations and design reports Produce AutoCAD drawings and technical sketches Review me...

Title: Civil Engineer Needed for BOQ from PDF Drawing Description: I am looking for an experienced Civil Engineer or Quantity Surveyor who can prepare a complete BOQ (Bill of Quantity) from a construction drawing PDF. Scope of work: - Quantity takeoff from drawing - Earthwork / Excavation - PCC and RCC calculation - RCC in footing, column, beam, and slab - Reinforcement steel quantity - BOQ preparation in Excel format Requirements: - Good knowledge of construction drawings - Experience in BOQ and quantity takeoff - Ability to deliver accurate calculations The drawing PDF will be shared after hiring. Please send your proposal with your experience in BOQ preparation..

Title: Civil Engineer Needed for BOQ from PDF Drawing Description: I am looking for an experienced Civil Engineer or Quantity Surveyor who can prepare a complete BOQ (Bill of Quantity) from a construction drawing PDF. Scope of work: - Quantity takeoff from drawing - Earthwork / Excavation - PCC and RCC calculation - RCC in footing, column, beam, and slab - Reinforcement steel quantity - BOQ preparation in Excel format Requirements: - Good knowledge of construction drawings - Experience in BOQ and quantity takeoff - Ability to deliver accurate calculations The drawing PDF will be shared after hiring. Please send your proposal with your experience in BOQ preparation..

Job Description We are a steel fabrication company in the UK looking for a mechanical engineer with experience in pressure vessel design to produce calculation report for some pressure vessels we will be manufacturing Provide engineering calculations for: • Shell thickness • Head thickness • Nozzle reinforcement checks (main nozzles) • Hydrotest stress verification • Confirmation that the vessel falls within SEP classification We are not requesting a certified design package — only a competent engineering calculation report for fabrication verification. A calculation report including: • Assumptions and design basis • Material allowable stresses used • Formula references / method • Required shell thickness • Required head thickne...

Project: Revit Structural + MEP Modeling and Clash Detection Project Overview • I have already completed the architectural model in Autodesk Revit. • I need assistance completing the structural, plumbing, and electrical layouts, and generating a clash detection report using Autodesk Navisworks. ⸻ Scope of Work 1. Structural Modeling • Create structural columns, beams, and foundations based on the existing architectural model. • Structural elements should align properly with the architectural layout. • Provide structural floor plans. 2. Plumbing Layout • Model plumbing systems including: • Water supply pipes • Drainage pipes • Basic plumbing fixtures connections • Ensure routing is realistic and coordinated with the building l...

I'm seeking an expert to help design a culvert and gravel driveway in a floodplain for a residential project (single home access). I am currently under contract on a parcel of land in Cabarrus County North Carolina. It will need an engineered culvert and gravel driveway design to cross a creek (20 feet wide). It is in a 100 yr flood zone. Cabarrus County Planning and Zoning said we will need a Floodplain Development Permit and I'm told that needs to include a flood study. The culvert and gravel driveway are all we are doing in the floodplain, the house and all utilities will be outside of it. The seller told us that the damaged culvert has been there for over 30 years and failed in early 2024 with the flooding that hit this area. It has two 24 inch concrete pipes. Key consider...

I am laying out five vertical cylindrical tanks for oil storage and need a complete structural package for the circular raft foundations that will sit beneath each vessel. The design must be fully compliant with API 650 requirements for tank foundations, including all load combinations relevant to oil containment. At this stage I will forward the geotechnical report as soon as it is released, so please allow for one round of adjustments once the actual soil profile is known. Until then, work with clearly stated provisional assumptions, noting how they will be revised when the clay / sand / rock condition is confirmed. Deliverables I expect: • Sizing calculations and design notes (PDF + editable file) • Reinforcement layout, bar schedules and anchor-bolt plan in CAD (DWG) and ...

I am finalising the structural scheme for a new industrial warehouse and need a fully-engineered steel truss solution that can reliably carry medium roof and service loads. Your package should include member sizing, connection details, and clear span optimisation so fabrication and erection can proceed without re-work. Please deliver: • Structural calculations that justify every section and connection • Editable CAD drawings (DWG) plus print-ready PDFs showing plan, elevation, sections, and details • A concise material take-off for procurement • A short design note summarising assumptions, load cases, and the code you followed I will review the calculations for consistency, check drawings against the architectural grid, and confirm that deflection and strengt...

I’m adding a 2 modest bedroom onto my existing cabin and need a licensed structural engineer to turn my architect’s concept sketches into stamped construction documents. The job is a straightforward room extension—no garage or porch involved—but I still require full structural calculations to satisfy local code and obtain the permit. Scope of work You’ll review the current house drawings (single-story wood frame), analyze loads for the new footings, walls, and roof tie-ins, and deliver clear plans my contractor can follow. The city wants engineered framing specs, beam sizes, connection details, and any shear/bracing notes. Soil reports and a basic site plan are ready for reference. Timeline Permit submission is scheduled for four weeks from today, so I n...

I need a temporary works designer for underpinning, specifically design calculations. The method of underpinning will be mass concrete underpinning. Ideal Skills and Experience: - Expertise in temporary works design - Strong background in structural engineering - Experience with mass concrete underpinning methods - Proficient in design calculations for underpinning systems - Relevant certifications in inspection and safety Please provide a portfolio showcasing similar projects and relevant qualifications.

I'm seeking an experienced structural engineer to perform critical calculations for a low-rise hotel. The primary construction material will be steel. We are looking to increase height of lobby entrance as well as add a rooftop bar on the roof deck. Key requirements include: - Load-bearing calculations - Wind and seismic analysis - Foundation design Ideal candidates should have: - Proven expertise in steel structures - Experience with low-rise buildings - Strong knowledge of relevant codes and regulations - Ability to deliver precise and reliable calculations Please provide examples of similar work and relevant qualifications.

I am seeking an experienced mechanical or FEA engineer to perform a static structural finite element analysis (FEA) on a plastic lid component made from Polycarbonate (PC-110). The goal of the analysis is to estimate the force required to cause yielding or failure when a load is applied at the center of the lid panel. A STEP file of the part and a detailed instruction PDF are attached here. The simulation should apply a load perpendicular to the lid surface over a 1-inch diameter circular area at the center, while the perimeter of the lid is constrained as shown in the attached instructions. The analysis should gradually increase the load until material yield occurs (Von Mises stress ≥ 9,000 psi). Deliverables should include a short simulation report (PDF), stress plots, deformation plo...

I'm seeking a Freelance structural engineer with a PI of £2million or over to develop detailed structural design for a residential building. I already have architectural plans ready for your reference, a good idea of the strucutral design we need. Key Requirements: - Expertise in structural design for residential buildings - Proficiency in interpreting and working with existing architectural plans - Knowledge of UK building regulations and standards - Strong analytical skills and attention to detail Ideal Skills & Experience: - Professional engineering degree and relevant certifications - Proven experience in residential structural design - Excellent communication skills for collaboration - Portfolio showcasing similar completed projects Submit your bids wi...

I need a small concrete pad (up to 4x4 ft) to support a steel post. The pad should be capable of handling a medium load, suitable for residential use, and will be placed on clay soil. Requirements: - Experience with concrete work - Understanding of load-bearing requirements - Ability to work with clay ground conditions

I have built several tractor-mounted boom extensions and now I want solid, engineer-backed numbers on exactly how much weight each point along the boom can safely handle. The boom is welded from a 3/8" side-steer plate and a 2-1/2" × 2-1/2" × 3/16" square tube. From the plate it runs straight for 10 ft, then kicks up at a 30° angle and continues another 2 ft, giving a total length of 11 ft 10 in. Its primary job is lifting pole-barn trusses, so the working load will sit in the 500–1,000 lb range. I don’t have to satisfy OSHA, ISO, or any other formal standard, but I do want a clear, defensible safety factor. What I need from you is a straightforward structural analysis—hand calculations, FEA, or a mix—that tells me: • Ma...

I need structural drawings for a 1,500 sq ft (30x50) post frame garage. Drawings must include framing details and be stamped in Arizona. Ideal Skills and Experience: - Experience in creating structural drawings for post frame structures - Knowledge of Arizona building codes and requirements - Proficiency in drafting software

I’m adding a full second story to an existing single-family home and need a local experienced architect who can take the project from concept through permit submission. The new level will house an open-plan living area that blends seamlessly with the ground floor and matches the home’s current traditional character—think compatible roof pitch, sympathetic window proportions, and exterior detailing that feels original rather than tacked on. Because this is a structural addition, on-site measurements and coordination with a local engineer are essential. You’ll prepare code-compliant drawings suitable for both planning approval and construction, work out framing and stair integration with my builder, and remain available for minor revisions requested by the city. ...

I need a licensed engineer to prepare and stamp complete plans covering two linked changes on my residential lot: 1. Replace the existing wood fence along the south property line with a block-and-aluminum design and shift it approximately five feet closer to the road. 2. Relocate the driveway from the current south-side entrance to a new approach on the east side of the parcel. The goal is mainly aesthetic improvement, but the drawings must satisfy all structural, zoning-setback and permitting requirements in my jurisdiction. I will rely on your signed and sealed plans to submit for city approval, so accuracy and code compliance are essential. Please include: • Site plan showing current and proposed fence line, new driveway alignment and any grading or drainage notes. • S...

For an upcoming marine‐grade manhole cover fabrication for a drilling rig, I need a formal Welding Procedure Specification that meets every clause of AWS D1.1. Manhole covers will be assembled and inspected in a shipyard environment, so clarity, practicality, and code compliance are equally important. The finished WPS must: • Reference AWS D1.1 throughout and spell out all essential, supplementary and non-essential variables. • Be tailored to marine-grade carbon steel; include pre-heat, inter-pass, post-weld and any corrosion-protection notes unique to salt-water service. • Specify filler metals, shielding gases and joint preparations suitable for both yard and onboard repairs. • Come with a Procedure Qualification Record template (or existing PQR data if you...

I need a skilled contractor to construct an in-ground, rectangular concrete pool. The project also includes necessary plumbing and electrical work. Key requirements: - Experience in civil construction, specifically with in-ground concrete pools - Proficiency in plumbing and electrical installations related to pool systems - Adherence to safety and building regulations Ideal skills and experience: - Relevant certifications in construction, plumbing, and electrical work - Previous similar project experience - Strong project management skills to ensure timely completion Please provide a detailed proposal with timelines and cost estimates.

I have a complete architectural layout and now need a full set of structural TMT rebar drawings so my site crew can move straight into steel-fixing. The scope covers three reinforced-concrete elements—the swimming pool, the underground water tank and the basement wall—with every bar, lap, hook and splice called out clearly. Your job is to translate the layout into construction-ready reinforcement plans, sections and schedules that follow our local building codes. All drawings must be delivered as clean, well-layered PDFs that scale accurately when printed on A1/A3. Deliverables • Plan, section and elevation sheets for the pool, tank and basement wall • Bar bending schedules with diameters, lengths and quantities tagged to gridlines • General notes sheet s...

I’m preparing a full design package for a new commercial road that must safely handle a mixed flow of light cars, motorcycles, heavy trucks, and buses. The brief goes beyond basic pavement geometry: pedestrians need dedicated walkways, cyclists must have protected lanes, and the junctions will be signal-controlled for efficient traffic management. The work starts at concept level and carries through to construction-ready drawings. Horizontal and vertical alignment, structural pavement layers sized for heavy axle loads, intersection geometry, drainage, signage, and complete traffic-signal layouts have to be covered. CAD output in Civil 3D, OpenRoads, or an equivalent professional platform is essential so the files can slot straight into our existing workflow. Deliverables • S...

Brief: Request for Consultant Services to Prepare Building Control Drawings and Specifications We are seeking a qualified consultant to prepare Building Control drawings and specifications to demonstrate compliance with current planning regulations for building extension under permitted development in England. Scope of services: • Review proposed extension design and site context. • Confirm applicability of permitted development rights (PD) and any planning conditions or Article 4 directions that may affect consent requirements. • Identify relevant Building Regulations (England) and standards that apply to the project • Produce clear, buildable Building Control drawings (plans, elevations, sections, and typical details) for the extension. • Prepare accompany...

I’m completing a new build in Hawthorn Woods, IL with a small grade change (5 to 6 foot) that calls for a Rochester Classic 6" segmental retaining wall. The village will not release the permit until the wall plans carry a current Illinois-licensed structural engineer’s stamp. Here is what you’ll receive from me: • Full architectural set for the house • Current plot of survey with proposed grading • A to-scale landscaper drawing showing the wall location, drainage stone, perforated pipe, and geogrid setbacks I still need you to: 1. Review and verify the landscaper’s drawing for accuracy against the survey and grade. 2. Recommend any tweaks that will improve stability or meet code before stamping. 3. Provide signed and sealed calculations and dra...

I’m adding a new 8-ft rear deck to my home in Weston, FL and need a Florida-licensed Professional Engineer to take my initial draft drawings (supplied as PDFs) through to permit-ready status. What I’m looking for is straightforward: review the structural layout, make any adjustments required for full Florida Building Code compliance, and provide a signed and sealed PE stamp on the final drawings so I can submit them to the City of Weston for permitting. Deliverables • Reviewed structural deck plans, updated as necessary • Digital PE-stamped drawings in PDF (and CAD if you edit directly) • Brief calculation or compliance memo if the permitting office requests it Everything is still at the early-draft stage, so I welcome practical suggestion...

I need to run a series of on-site load tests on several fixed posts installed in a confined area. Space restrictions mean the whole setup must rely on a compact, portable hydraulic arrangement rather than large jack systems or heavy rigs. The main goal is to confirm and fine-tune the posts’ performance under their design loads—this is strictly about performance optimization, not a one-time safety check. All procedures, calculations, and reporting have to align with the relevant international building standards, so any methodology you propose should reference the specific clauses you intend to follow. I will supply drawings, design loads, and access details once we start; you will handle everything from test plan to final report. Deliverables • A concise test plan showi...

I already have the structural designs for a swimming pool, a clint beam underwater tank, and a basement RCC retaining wall compiled in PDF format. What I am missing—and what I need you to provide—are full construction-ready TMT rebar drawings that a site crew can build from straight away. Your work must translate every dimension, bend, lap, hook, and cover into clear reinforcement detailing that satisfies all applicable local building codes. Accuracy is critical, so please be comfortable working from PDF references and extracting every nuance needed for a compliant bar bending schedule. Deliverables I expect: • Layered CAD drawings (DWG + PDF plots) showing plan, section, and elevation views for each structure • A complete bar bending schedule with diameters, shap...

Value Engineering – Analyze the design to find cheaper alternatives that keep the same strength, durability, and function. Structural Design Optimization – Use structural analysis software like ETABS and to avoid over-design and reduce unnecessary steel and concrete. Efficient Column Grid Planning – Plan regular spacing of columns and beams so the structure uses materials efficiently and construction becomes simpler. Use High-Strength Concrete Only Where Needed – Select the appropriate concrete grade based on structural requirements instead of using high grade everywhere. Partial Cement Replacement – Use materials like Fly Ash or Ground Granulated Blast Furnace Slag to reduce cement cost and improve durability. Precast Construction – Use factory-made el...

I need a structural steel engineer for a renovation project where the entire roof is being replaced with a pitched roof. The engineering services required are design and drafting, as well as load calculations and material analysis. Provision of drawings for council approval - Shire Kalamunda. Key requirements: - Design and draft structural steel plans for a pitched roof. - Perform load calculations and material analysis. - Collaborate with builders and council for compliance. Ideal candidates will have: - Proven experience in structural engineering for pitched roofs. - Strong knowledge of load calculations and material properties. - Ability to provide detailed, compliant design drafts. Looking for a qualified professional to ensure a safe and reliable roof structure.

I'm looking for an experienced designer to modify an existing office layout into a positive pressure cleanroom using modular partition walls with integrated glass windows. Key Requirements: - Structural design for ceiling to support positive pressure - Modular partition walls - Glass windows (single or double pane) Ideal Skills: - Experience with cleanroom design - Knowledge of positive pressure systems - Proficiency in modular wall systems and structural ceiling design Please provide relevant experience and any similar projects completed.

I am moving ahead with a multi-storey residential project—at least six floors plus a full basement—and need a complete reinforced-concrete structural package. The frame must integrate shear walls for lateral stability and several cantilevered elements, so experience detailing those features is essential. Scope You will run the full analysis and design workflow, preferably in ETABS, SAFE or an equivalent platform, then turn the results into construction-ready documents. All work must satisfy the latest Indian codes (IS 456, IS 875, relevant seismic provisions) and local authority submission formats. Deliverables • Structural analysis model files • Design calculations for beams, slabs, columns, shear walls, basement retaining walls and cantilevers • Reinforce...

Architectural designer for preparing architectural drawings such as plans, elevations, and finishes for oil and gas substation buildings. The Building size is 50x200m